Semiconductor Chiller
|
Semiconductor Chiller
Semiconductor Chillers- Over the years,
Legacy Chiller Systems has built a solid reputation for
developing efficient and reliable "Mission Specific" fluid
cooling solutions for a wide range of applications from
laser chillers to wine chillers. Today, many fortune 500
companies who produce fluid-cooled applications recommend
Legacy's products and services to offer their end-users a
better integrated chiller package.
Below are just a couple of the many
features of the Semiconductor & General high tech Chillers:
SEMI-HERMETIC PACKAGED AND SPLIT
SYSTEM
AIR COOLED CHILLERS
(1-90 Nominal Tons)
STANDARD FEATURES
- Legacy microprocessor controller
- Control transformer
- Refrigerant suction accumulator
- (1-12 HP) 316 STAINLESS STEEL (copper brazed) plate
evaporator with ½” insulation and secured in a steel bracket
- (15-120 HP) shell and tube chiller barrel
- Water flow switch
- Condenser fan and control circuit fusing
- Semi-Hermetic compressor with crankcase heater
- Compressor vibration eliminators & spring isolator kit
- Compressor oil safety control
- Compressor and condenser motor contractors
- Direct drive condenser fan motor
- Fan cycle control (+40 F)
- Rust resistant, high CFM, aluminum condenser fan blade
- Condenser(s): copper tube / aluminum fin
- Condenser clean out ports
- Liquid line drier, sight glass, solenoid, TEV
- Replaceable core liquid line drier (15-120 HP)
- Removable hinged access panels
- Galvanized steel sheet metal cabinet & base frame
- ½” insulation on all water and refrigerant suction lines
- Complete refrigerant charge from factory
- Computerized factory run test under load conditions
AVAILABLE OPTIONS
- Compressor cylinder unloading 7.5 Hp & up
- Compressor fusing
- Fused disconnect
- Flooded condenser with receiver and head pressure control
(-20 F)
- Flooded condenser with heated receiver and head pressure
control (-20 F)
- Factory installed heat tape freeze protection
thermostatically controlled
- Special piping for de-ionized and reverse osmosis water
systems
- Shell and tube chiller barrel (1-12 HP)
- Fused STAINLESS STEEL system process pump
- Dual system process pump with manual or auto changeover
- Water flow meter
- Phase monitor
- Condenser heresite coating (coastal protection)
- Copper condenser coil (coastal protection)
- “Gold” finned condenser coil (coastal protection)
- 4 year extended compressor warranty
- Hot gas by-pass capacity control with solenoid valve &
time delay relay
- Factory assisted start-up
SPLIT SYSTEM / EVAPORATOR SECTION
SINGLE / DUAL CIRCUIT
STANDARD FEATURES
- Legacy microprocessor controller
- (1-12 HP) S.S. brazed plate evaporator – (Only available
for Single Circuit Systems)
- (15-120 HP) shell and tube chiller barrel
- Water flow switch
- Suction accumulator
- Remote Condenser
- Condenser fan and control circuit fusing
- Condenser fan motor contactors
- Semi-hermetic compressor with crankcase heater
- Compressor vibration eliminators & spring isolator kit
- Compressor motor contactor
- Compressor oil safety control
- 24V control transformer
- Liquid line drier, sight glass, solenoid, TEV
- Refrigerant discharge / liquid access valves
- Galvanized steel base frame
- ½” insulation on all water and refrigerant lines
- Complete refrigerant charge from factory\
- Factory run test under load conditions
TANK SECTION
(30 to 600 Gallon Capacity)
STANDARD FEATURES
- STAINLESS STEEL storage tan
- ½” tank and fluid piping insulation
- Copper fluid piping
- Tank vent and drain connections
- Tank pressure relief valve
- Fused evaporator fluid re-circulating STAINLESS STEEL pump
- Fluid pump discharge ball valve and cleanable “Y” strainer
- Control box with pump terminal block
- Painted galvanized steel sheet metal cabinet
- 24V L.E.D. process fluid thermometers
AVAILABLE OPTIONS
- Fused STAINLESS STEEL process pump
- Tank fluid sight glass
- Tank liquid level indicator with dry contacts
- STAINLESS STEEL piping for reverse osmosis or de-ionized
water applications
- STAINLESS STEEL sheet metal cabinet
- 1” tank and piping insulation in lieu of ½”
- Seal-tight electrical connections
|
|
|
|
